Thursday, June 9, 2011

The carving begins



I own a nice selection of really good vintage carving tools that fill up two drawers in my large Gerstner tool chests. I don't know why I bother buying additional gouges because I always seem to end up using the same one for 99% of the carving that I do. My favorite carving tool is J B Addis 1" #6 sweep gouge. The 1" refers to the width and it is a standard way of denoting chisels and gouges. The # 6 sweep refers to the shape of the curve and that is less uniform. Addis tools are what are commonly referred to London pattern. And there is some evidence that James Bacon's (the J B of J B Addis) brother, Samuel James Addis, created the London Improved Pattern of carving tools. In the London pattern the # of sweep refers to the number of repetitions of the width of the tool that are required to make a complete circle. So this means that my favorite gouge is 1/6 of a circle. The confusing part of this way of denoting the sweep is that a 1/2" wide #6 sweep will have a completely different curve to it than my 1" wide #6. The way the sweep of gouges on most modern tools are denoted the same # sweep in different widths will have the same curve, just shorter segments of that curve. The problem with this very logical approach is that not all modern makers use the same standard curves in their numbering of the sweeps. With the London pattern a circle is always a circle and 1/6 of a circle is always 1/6 of a circle regardless of the radius of that circle.

It can be difficult to determine the date of manufacture for J B Addis tools but I do know that some of mine date back to the mid 1850's. All of the Addis tools I own are beautifully made and a pleasure to use, but being individually hand made there are a few that are just a little bit better than the others. The remarkable thing about the Addis tools is that in that period Sheffield is widely regarded as the steel making center of England and the edge tool makers there were widely regarded as making the best quality tools. At the time the trade unions and guilds were very strong and tool steel from Sheffield would never have been sold to a tool maker in London. Yet the Addis brothers made some of if not the finest carving tools ever made.

I might seem to go on a bit about my preference for the tools I use but part of what makes my tools so special to me is the handles. It took me several attempts before I found the shape and size of handle that worked best for me, but once I did it is a handle that is custom tailored to the size of my hand and where I pace my thumb and fingers. As much as I like the shape of my handles part of what makes them so successful is the chinese elm they are made from. Chinese elm is so hard and tough that it allows me to push the handles of my tools with the palm of my hand as well as strike them with a mallet. This may not seem like a big deal but most combinations of handle design and wood will end up with a mushroomed or deformed end when struck with a mallet and this will in turn cause a blister when trying to subsequently push the tool with your palm.

As important as my chisels and gouges are a synergistic relationship exists with the mallet they are used with. You can see my mallet in the picture and it is not terribly unique in its design. It is something I made out of chinese elm about 15 years ago, remarkable when you consider the tens of thousands of strikes it has made and still looks as if it has rarely been used.  It may seem like any mallet would do the job and to some extent I suppose that is true. Still it is important that the handle fit well and the weight be enough to drive the tool in the wood yet not so heavy that it is tiring to use. When carving with a mallet I make rapid strokes and the focus of my eye and all my attention is at the working edge of the gouge. I do not think about the angle I am holding the handle of the gouge at, and I am not looking at the handle when I strike it with the mallet. The mallet in essence becomes an extension of my hand and the striking action is one that becomes intuitive. It takes a bit of practice to be able to carve this way but it is practice well spent.

I prefer a strong low raking light when carving in addition to the overhead lights in my shop. The light is the pictures is easily adjusted to highlight the shadows created by each chip removed and makes it easier to see what I am doing.
Robin



No comments:

Post a Comment